Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 40

Thread: FAQ from MOBILE-FILES.COM

  1. #21
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    Q: i have emptyboard phone. how to convert it to normal ?

    A:

    warning ! steps are important.

    for db2000/db2010:

    1. go to empty board tab
    2. select needed model, on settings tab: uncheck all settings.
    3. select needed cid
    - select cid53 for all NEW SECURITY db2012 phones (w200/k320/latest W810/etc)
    - select cid49 for all "modern" phones,
    - select cid36 for "old" phones (k700,k500,s700,k300),
    - select cid29 for ancient z1010
    3. press recovery
    5. if board is totally empty (new flash chip), select needed gdfs_in_ssw_format
    6. select respective EROM (if phone need EROM) from EROMs folder
    7. fill IMEI number, check WRITE OTP (it can be done only once, be careful)
    Code:
     DOUBLE CHECK THAT "OTP CID" (WHICH YOU SELECTED) LOWER OR EQUAL TO EROM CID 
    8. press flash

    phone now normal retail and can be serviced as any other phone.


    for db2020.

    1. go to empty tab
    2. select any db2020 model, on settings tab: uncheck all settings
    3. select cid49 (that is REQUIRED)
    4. press recovery
    5. if board is totally empty (new flash chip), select needed gdfs_in_ssw_format
    6. select respective EROM
    7. fill IMEI number, check WRITE OTP (it can be done only once, be careful)
    Code:
     DOUBLE CHECK THAT "OTP CID" (WHICH YOU SELECTED) LOWER OR EQUAL TO EROM CID 
    8. press flash

    phone now normal retail and can be serviced as any other phone.


    a little example of emptyboard filling for db2020 :

    count db2020gdfs_in_ssw_format_CID49_BROWN.ssw.cry as empty "template" of GDFS.
    that template should be written on empty flash chip during emptyboard filling process.

    then you can write gdfs in .binary format on semc tab, check phone and if all ok - close OTP.

    Code:
    so, lets assume we have 
    1. k810 with empty flash chip
    2. db2020gdfs_in_ssw_format_CID49_BROWN.ssw.cry
    3. k810gdfs.bin
    
    1. go to empty tab
    2. select cid49, press recovery
    3. add to fw tab DB2020EROM_CNV_RED52_BROWN_CID49_DB2020.ssw (example),
       db2020gdfs_in_ssw_form at_CID49_BROWN.ssw.cry, press flash
    4. go to semc tab, flash any situable main firmware
    5. on semc tab, write k810gdfs.bin using "write gdfs" and misc. edit.
    6. back to empty board
    7. select cid49, press recovery
    8. add to fw tab DB2020EROM_CNV_RED52_BROWN_CID49_DB2020.ssw ,press flash
    9. go to semc tab, flash complete firmware (main+fsimage+custpack) 
    OR just flash fsimage,situable to main,written on step4 +custpack
    10. now check - phone should be able to turn on normally
    11. finally, write IMEI and write OTP, for that 
    12. go to empty board,select cid49, press recovery
    13. add to fw tab k610_erom_cnv_brown2red.cry,fill IMEI, 
         check "write OTP", press flash.
    important!
    use only EROMS from setool2 dist\eroms folder - they are resistant for EROM UPGRADE feature (means yours phone will stay not damaged after emma/etc)

  2. The Following 6 Users Say Thank You to GSM™ For This Useful Post:


  3. #22
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default FAQ on SETool new support area access

    How to enter new support area?
    Download latest version of Supporter software from www.setool.net, start it and press "GO SUPPORT" button. Also you can enter support area from SETool software by pressing the same button (v0.91380070 and higher).

    Why did you change support system? Get all back!
    Old support system will not be installed back. Users and administrators are more satisfied with new one. Please no more discussions on this topic.

    Very slow downloading
    Approximate download speed per peer is 50Kb/s. If your download speed is slower, it seems, that your internet provider has too narrow connection to the direction of SETool support server location. Unfortunately, we cannot deal with this problem. You need to check your internet connection

    Cannot connect to server/Cannot display page/Connection has been reset, mysql reports error, etc.
    Maybe server is currently down. Please create one (only!) topic in this section and wait until support access will be restored. If such topic already exists, no need to even post in it. It is enough for us that it exists to pay attention to problem

    Resuming downloads
    Download resuming is supported. You should use it if possible. Please pay attention to the fact that several Download Managers are incorrectly use features of HTTP protocol, incrementing by this daily download counter by 2 instead of one. I checked FlashGet only. It is working fine. Cannot say something about the others.

    Errors list explained

    Your account is suspended by admin. Please contact your reseller.
    Please contact your reseller. Don't spam forum. Contact your reseller first and do as he says.

    This link is already used. Please relogin from software.
    If you closed browser window, you need to relogin to support area from software only.

    Please login from soft only
    Please ensure you entered support exactly from software. If you did so, then probably the problem is in the fact, that your browser does not accept cookies. You need to set it up to allow cookies at least from setool.net. If you will still get this error with IE, download Mozilla FireFox, install it and make default browser: http://www.getfirefox.com.

    Wrong IP. Please relogin from soft
    Your IP is changed during browsing support area. Please relogin from software.
    Please ensure also, that you don't use proxy server for internet surfing.

    This session is expired. Please relogin from soft
    Just relogin from software.

    You have exceeded your today's download limit
    Just wait for the next day for daily download limit to be reset.



    If there is no answer to your question in this FAQ, please create one (only!) topic in this forum, clearly describe your problem and wait for us to answer. If such topic already exists, don't create another one.

  4. The Following 2 Users Say Thank You to GSM™ For This Useful Post:


  5. #23
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    Q: after i made csca unlock on k320 phone (or other) i have 5-locks in service menu and phone not accepting any card.
    what to do ? i lost x logs !!!

    A:
    Welcome to SEMC "security addon".
    in such case you must

    1. select in "misc. edit" file
    %setool%\backup\%imei%_%datetime%.fixup (created from version 076)
    2. execute "write script".

    if you restored .seczone file by accident ( unwise ) - you MUST repeat CSCA unlock (lose another 4 creds) and go to step 1.

    important addon

    that bug is fixed in R4GC012 firmware series (for k320,w810 phones)
    so, if you lost somehow (?) your original .fixup, just flash phone with R4GC012 firmware and redo CSCA unlock.

    alternatively, you can just unlock phone using reset procedure.

  6. The Following 3 Users Say Thank You to GSM™ For This Useful Post:


  7. #24
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default How to use custpacks.

    Question:
    "What are custpacks, and how do I use them?"

    Answer:
    Custpacks are zip-files containing ORIGINAL customization files. These serve as basic configuration files for the handset, which languages to allow, data accounts, branding etc...

    Using custpacks is preferable to checking "COMPLETE PHONES AFTER FLASH" in "Settings". "Complete..." uploads a "working" customization, but the files are not handset-specific and their use might lead to the following:
    1: Phone won't work with SEUS.
    2: Phone will be refused at a service-center as EMMA might pick it up, and that it's pretty obvious that the phone has been "tampered with".
    3: Software ****ups.
    4: Etc...
    Now, some of the above will be avoided by using custpacks. I''ve attached some screenshots to demonstrate their use.

    Screen one:
    Select a proper MAIN/FS combination (duh...). Then select the desired custpack in MISC. SETool => v.0***77 will tell you which languages it contains/allows, the CDA etc.
    Screen two:
    Uncheck "Complete..." in "Settings".
    Press FLASH.

    Screens three and four serve only as a map for finding custpacks @support. In my example, the selected custpack will configure the K750 as a generic EUROPE_4 one. It is found inside the large K750 custpack archive. Other handset custpacks might have been uploaded separately. Just look for the desired CDA.

  8. The Following 3 Users Say Thank You to GSM™ For This Useful Post:


  9. #25
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    Some questions with some answers...

    Q: How can i know wich CID is my phone?
    A: Press "IDENTIFY"

    Q: Can i change IMEI on my PDA?
    A: If is NEW SECURITY, no, you can't. If is OLD security, you can do it.

    Q: After unlock my K310/K510/W300/W810/Z530/Z550 CID50/51 phone is dead and rest was present. What must i do?
    A: reMake RESToration file and repeat procedure.

    Q: If i unlock a phone using patch metodh, will be blocked if flashed?
    A: Yes, phone will be locked again

    Q: If i unlock a phone using patch metodh, will be blocked if flashed again using Alternative Bypass?
    A: phone will be unlocked if you check "UNLOCK DURING FLASH" option.

  10. The Following 4 Users Say Thank You to GSM™ For This Useful Post:


  11. #26
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    Here is Language Description for A2 phones (W910, V640, K850, Z750 and newers...):

    FS_BALTIC: English, Estonian, Latvian, Lithuanian, Russian
    FS_HONG_KONG: English, Chinese (Hong Kong)
    FS_NORDIC: English, Albanian, Arabic, Croatian, Danish, Finnish, IS, Norwegian, Swedish, Turkish
    FS_WESTERN-EUROPE: English, Euskara, Catala, Dutch, French, Galego, Portuguese, Spanish, Turkish, Nederlands.
    FS_ADRIATIC: English, Albanian, Bulgarian, Croatian, French, German, Greek, Italian, Romanian, Russian
    FS_AMERICA: English, Portuguese, Canadian French, Dutch, French, Latin American Spanish, Spanish
    FS_APAC-ANZ: English, Dutch, French, German, Malay, Indonesian-Bahasar, Philippine-Tagalog, Thai, Vietnamese, Chinese simplified
    FS_C-ASIA: English, Arabic, AZ, Persian-Farsi, KK, Russian, Turkish, Ukrainian
    FS_CENTRAL-EUROPE: English, BS, Croatian, German, Czech, Hungarian, Polish, Serbian, Slovakian, Slovenian
    FS_FRANCE: English, French
    FS_S-E-EUROPE: English, Albanian, Bulgarian, Croatian, Greek, Hungarian, Macedonian, Romanian, Russian, Serbian
    FS_S-ASIA-LEVAN: English, AR, AZ, BN, Persian-Farsi, French, Philippine-Tagalog, Hebrew, Hindi, Russian
    FS_S-CENTR-AFR: English, AR, Dutch, Persian-Farsi, HA, German, IG, Sesotho (South Africa), YO, Zulu, Portuguese
    FS_TAIWAN: English, Chinese traditional Taiwan

    Languages like "AR", "AZ", "YO", etc are unknow yet (at least for me).

  12. The Following 2 Users Say Thank You to GSM™ For This Useful Post:


  13. #27
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    SETOOL WINDOW OR SOFTWARE DISAPPEARS WHEN I TRY TO CONNECT TO A PHONE

    Reason - You have a virus, trojan, malware or other memory resident software that is trying to debug Setool software.

    Solution - Run a full virus scan with a QUALITY commercial virus scanner such as Norton 360, NOD, Kaspersky etc. Free solutions such as Avast and other public domain software will not fully remove the offending software (they may not even detect the virus). You may also consider installing software such as Adaware or another spyware detection

  14. The Following 4 Users Say Thank You to GSM™ For This Useful Post:


  15. #28
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    some handy scripts for a2 phones (you know how to write script, right ? )

    a2_enable_3g.txt
    gdfswrite:0000013C00
    a2_amr_hr_on.txt
    gdfswrite:00000152020004050F
    a2_amr_hr_off.txt
    gdfswrite:000001520200040F0F
    a2_amr_fr_on.txt
    gdfswrite:00000152020004050F
    a2_amr_fr_off.txt
    gdfswrite:000001520200050F0F
    a2_efr_on.txt
    gdfswrite:00000152020004050F
    a2_efr_off.txt
    gdfswrite:000001520004050F0F
    a2_ciphering_indicator_on.txt
    gdfswrite:0000147301
    a2_ciphering_indicator_off.txt
    gdfswrite:0000147300

  16. The Following 5 Users Say Thank You to GSM™ For This Useful Post:


  17. #29
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    K850 - Keyflex update

    Description
    There has a quality problem with the K850 keyflex (1200-2656) causing touchkey problem.

    When pressing a touchkey, the visual indication in the lower part of the display will not work, nor will the actual touchkey. This may be intermittent as there might be microscopic cracks in the solder joints of the affected component that is soldered onto the keyflex.


    Solution:
    use new keyflex.

  18. The Following 4 Users Say Thank You to GSM™ For This Useful Post:


  19. #30
    Super Moderator
    Join Date
    Feb 2010
    Location
    MySQL
    Posts
    41

    Default

    important information:
    Code:
    K800 and K790 will also start use the new RNH 942 271 LCD in production 
    which requires R8BF003 software.
    
    CS will continue to use RNH 942 268 LCD as sparepart that works with any
    software revision.
    
    The RNH 942 268 part no. is found on the label on the LCD flex foil.
    Code:
    in short, bulletin means that some k800 and k790 MUST be flashed 
    with R8BF003 software in order to display something other,than white screen.

  20. The Following 4 Users Say Thank You to GSM™ For This Useful Post:


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •