-
v0.91380071
first, and most important news.
you are not required now to register on support or use login/password to login on support area.
all you need - download software from www.setool.net, install drivers and press GO SUPPORT button.
- added some missed models...
- fixed some cosmetic bugs
-
The Following 7 Users Say Thank You to the_laser For This Useful Post:
-
v0.91380072
- made 5-times retry of each AT-query during csca unlock step2 (should help when phone drivers installation not finished)
- locks tab not works correctly when USB was used as selected interface
- some cosmetic fixes
-
The Following 7 Users Say Thank You to the_laser For This Useful Post:
-
v0.91380073
- changed csca unlock step1 behaviour. now, if there is ANY *.seczone files in %setool2%\backup\%imei%\ folder,step1 (erasing locks and writing signature) is skipped and step2 executing immediately. That is done to prevent credit loss if on step2 phone drivers installed incorrectly or if server connection broken on previous attempt of step2.
if you ABSOLUTELY know what are you doing - you can erase *.seczone files from %setool2%\backup\%imei% and step1 will be executed again for that phone.
- added "dummy battery" option for UFS cables with "crocodile" or otherwise called "dummy battery". if you check that option - before each phone shutdown we will execute grace delay to allow phone loader finish its work (for example, without that option you CAN get a "configuration error" on phones after flashing them using UFS and cable with dummy battery). grace period length is 5 seconds by default, but it can be changed with option "ufs_dummy_delay" in [main] section of setool2.ini (period counted in ms, so ufs_dummy_delay=5000 is 5 seconds)
- very minor ui bugfixes.
-
The Following 7 Users Say Thank You to the_laser For This Useful Post:
-
v0.91380075
Thursday, 22 March 2007
- added db2020 cid52 server support (flash,erom upg,usercode reset, network unlock (when we will restore server functionality))
- added db2012 cid51 server support ( flash,usercode reset, network unlock)
- added pnx5230 (Z310) cid51 server support (flash,usercode reset, identify NOT supported yet,network unlock (when we will restore server functionality))
- now all simlock types displayed in identify (state shown only if lock is locked)
- changed .ini file handling, so you must again rebuild settings. now settings for phones COMMON for all windows, beware. from now on settings will be intact when new models will be added.
- added new phone model names
- many internal changes,so please check for bugs.
w200 r1gb001 cid51 firmware uploaded
z310 r1jc002 cid51 firmware uploaded
k610 cid52 firmwares uploaded
k800 cid52 firmwares uploaded
w850 cid52 firmwares uploaded
db2020_firmware_in_gdfs_format added in distr.rar for completely blank boards. phones.rar updated with z310 driver for csca unlock
IMPORTANT ADDON. SADLY TO SAY (BLAME ME) -I NOT CAREFULLY ENOUGH
LOOKED AT Z310 - SO - DO NOT NETWORK UNLOCK Z310 - IT WILL BE DEAD.
OF COURSE, YOU CAN ALWAYS RESTORE IT TO "LIVE" WITH SECURITY BACKUP,
WHICH IS DONE AUTOMATICALLY IN "BACKUP\%IMEI%\%IMEI%_%DATETIME%.SECZONE"
YOU NEED WRITE IT AS SCRIPT.
-
The Following 7 Users Say Thank You to the_laser For This Useful Post:
-
v0.91380076
Monday, 26 March 2007
- corrected pnx5230 (z310) CSCA handling to prevent log loss and phone "damage". once again i remind that pnx5230 using same security as db2020 and we limited now to flashing and userlock reset (until we find some way to run server)
- included cid49_51_to_cid52 conversion. better not use it... really.
WARNING. DUE MISTAKE, FIRST 076 VERSION WAS
RELEASED WITH SERIAL CHECK ROUTINE ENABLED.
IT IS REPLACED NOW WITH "NORMAL" VERSION.
SO EVERYBODY, WHO DOWNLOADED 076 AND RECEIVED
"WRONG SERIAL" ERROR - REDOWNLOAD DISTRIBUTIVE.
SORRY FOR THAT AND THX FOR UNDERSTANDING
K810 r1kc001 CID52 firmware and customization packs uploaded
K790 r1cc003 CID52 firmware uploaded
K790 r1cg001 CID52 firmware uploaded
K790 r1eg001 CID52 firmware uploaded
K790 r1gb001 CID52 firmware uploaded
K790 r1jc002 CID52 firmware uploaded
K790 r1jg001 CID52 firmware uploaded ( K790 customization packs updated. )
-
The Following 6 Users Say Thank You to the_laser For This Useful Post:
-
v0.91373018
returned to old version of execryptor. GUI v0.91380009
- added FULL RED CID49 NO TESTPOINT support for NEW W500/W600, NEW K600/V600/K608, W900, see notes below
- updated "direct flash patching" for new sharp 703/903 firmwares
- testpoint usage allowed on sharp phones now
- testpoint usage reduced during operations
- added profiles support
- added "phone id" button (test cable, recognize phone cid,etc)
- slightly tuned ignition on ufs/com/dss - must be better
- fixed imei changing problem on w550/w600 in no-tp mode.
- some other internal modifications
- new bugs (unknown yet)
notes on REDCID49 support.
first. it must work only on non-touched (new) phones.
if phone was "tuned" with other software - no any warranty, but, generally, it should work.
second.
during ANY operations red49 phone became unusable (dead) until you flash so-called "restoration" file or flash "main" part of phone flash.
i prepared restoration files for most versions of red49 firmwares,they resides in "rest" folder of setool2 distribution.
usage of restoration file is simple. just determine your firmware version and select corresponding restoration file in "restoration file" edit.
if your unlucky and there is no restoration file for yours version of firmware, then you must fullflash phone (WITHOUT TOUCH TO GDFS AREA), just main+fsimage+complete.
third.
during flashing w900 phones on some (i think most) com cables, CHECK option "disable USB" - phone somehow assumes it is on usb, but it is on com
fourth.
well, no more to say - go, try, cry or enjoy. preliminary beta testing shows
good percentage of success (99.9%)
some example:
q: i have red49 w550, i don't know what firmware version inside, i want it unlocked and russian.
a:
go to semc tab.
press clear names.
select needed w550 flashfiles (main,fsimage). russian inside emea1
go to settings tab. CHECK complete. CHECK "unlock after flash". UNCHECK "revert to red.
go to semc tab, press flash
when prompted, remove and insert battery, press button "testpoint ok"
phone must be unlocked and flashed.
q: i have k600, i want to unlock it, i know that inside r2ae001 version.
a:
select in "restoration file" edit correct restoration file.
press unlock.
when prompted, remove and insert battery, press button "testpoint ok"
phone must be unlocked and restored, means - working.
NOTES ON PROFILES
button "S" saves all files and settings for current model.
button "L" restores saved files and settings from current model.
profiles works on sharp,lg,semc tabs.
profiles common for all windows.
enjoy, friends.
ps.
as usual, my personal **** to zuko. you can steal, but you can't create.
my personal greetings to mighty lead, who defeated upcoming db2020.
hope you will at least laungh on my cid49 method and show us, how to do red49 properly.
and my personal ask to all mighty hackers - please, stay aside from setool. better hack something more interesting
-
The Following 14 Users Say Thank You to the_laser For This Useful Post:
-
k310 firmware and customization files updated
-
The Following 8 Users Say Thank You to the_laser For This Useful Post:
-
some unusual w810 rest files attached.
some unusual w300 rest files attached.
-
The Following 6 Users Say Thank You to the_laser For This Useful Post:
-
v0.91380055
- user lock was incorrectly displayed if digit numbers uneven. fixed
- lg3g patching will be faster on SOME firmwares.
- added SERVER-based support for FLASHING, standalone support for usercode read for new SEMC smartphones
- m600/m608/w950/w958/p990.
carefully read instruction - that will help you NOT to kill expensive thing.
instructions.
first, you need download needed firmware package.
add it to firmware area on smartphone tab.
check "use server" and enter your login/password.
now, you need install drivers for flashing.
for that, poweron smartphone in fw update mode.
- for p990/m600 press and hold "@" on TURNED OFF phone, then attach dcu60.
- for w950 press and hold "C" on TURNED OFF phone, then attach dcu60.
windows will ask you for a drivers. drivers in %setool2 dist%\drivers\HermioneDrivers. i attached a picture how correctly installed drivers must look in device manager.
now, you can press desired operation.
identify - to readout phone information (and userlock)
flash - to flash package.
!note. there is a checkbox named "process PDA update files" if you UNCHECK it - NO CREDIT WILL BE DEDUCTED from your account, but CDA will be UNCHANGED in phone. you got me ? ( got, lol ) yes, that is FREE FLASHING.
!note. if you flashing multiple smartphones, BE SURE THAT DRIVERS ARE INSTALLED BEFORE starting desired operation.
read gdfs - read gdfs for different things.
write gdfs - write gdfs back.
!note. if you write gdfs from other phone, say bye-bye to yours expensive pda.
well, enough.
lets flash'em.
ps.
p990 flashes will be uploaded in next day-two.
-
The Following 6 Users Say Thank You to the_laser For This Useful Post:
-
v0.91380077
Tuesday, 17 April 2007
- "err: 10" error when z530 recovery operation executed fixed.
- customization packs now parsed when selected (shows language info,etc)
- added phonebook extraction from gdfs .bin format dump (NOT SSW).
usage is simple: select .bin file into misc. files edit, gdfs will be
parsed and .vcf file will be created.
phonebook unit is courtesy of PANUA, thx to him.
- all CID>50 now assumed to be used with auth dongle, to prevent credits loss.
- identify working now on USB interface
(in some cases reduced loaders are used, warning is displayed in such case)
- some other not important fixes (bugs ? )
-
The Following 5 Users Say Thank You to the_laser For This Useful Post:
Tags for this Thread
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks