Results 1 to 8 of 8

Thread: HOW TO WORK WITH SEMC ODM PHONES

  1. #1
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default HOW TO WORK WITH SEMC ODM PHONES

    some basics

    SEMC ODM phones divided on two big branch:

    obsolete cheap phones,where each phone has own specific approach
    j110,j120,j210,j220,z300,k200,k220,etc

    this phones don't have anything common with SEMC structure.

    Current generation, so-called S1 phones - they based on TI chipsets, STEricsson (former philips) chipsets
    j132,z320,t250,w302,f305,s312,w100,w150,etc.

    this phones has S1 SOMC structure: color,cid (aid), signatures,etc.


  2. #2
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default

    FLASHING OF SEMC S1-BASED ODM PHONES

    1. select correct model
    2. use com/ufs/usb as interface
    3. check "signed mode"
    3. add to firmware area needed firmware files
    4. press flash

    notes:
    some old locosto s1 phones do not support USB as interface

    if you want to flash brown firmware or readout, step 3 will be:
    3. check "signed mode","alternative security bypass"


    about SEMC S1 ODM files structure:

    1. neptune-based (w302,s302,f305) , ST-Ericsson-based (w100,w150)

    firmware contains 3 required parts:
    - main (ex: R1BA017_1207_9123_GENERIC_HS_YG_RED.software)
    - fs (ex: R1BA017_1207_9132_FS_ADRIATIC_HS_YG_RED.software)
    - customization (ex: R6A_F305_CDF_1215_9665__FS__Entel_PCS_CL.software)
    you need to flash all 3 files to get phone working with desired languages.

    F305, S302, W302 SW flash should be done without memory card inserted.
    If memory card is inserted during flash the flash can fail.

    If you encounter this problem,the phone does not startup correctly after flash, please wait 2-3 minutes
    then reinsert the battery and start the phone again.
    The phone should now start normally and the SW has been correctly updated.
    Please note that the SW is flashed correctly and this will not cause any future startup problem.

    2. locosto arima (t250,t280,k330,t303,r300)
    contains 2 required parts
    - main + language R5CA005_OLGA_ARIMA_AMERICA_2_CXC1251008_RED.softwa re
    - customization R7A_CDA102866_307__FS__Movistar_Guatemala.software
    3. locosto foxconn (z250,z320,r306,j132)
    - main R1BA008_1212_9858_MC_JIALI_RED.software
    - icons R1BA011_1211_6339_ICN_JIALI_RED.software
    (this files reside in archives like MODELx_FWVER_common.rar)
    - fs+language R1BA008_1211_6093_MALAYSIA_JIALI_RED.software
    - custpack R9A_R306_CDA_1212_6282__FS__Customized_SG.software


  3. #3
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default

    UNLOCKING OF SEMC S1-BASED ODM PHONES

    server-based full signature method

    1. select correct model
    2. on settings, check "signed mode", "do full unlock instead of usercode reset"
    3. back to odm tab
    4. press unlock

    that method can fix damaged security zone.
    that method depends of external service, so it can be offline any time.

    standalone patch method

    1. select correct model
    2. uncheck all settings
    3. back to odm tab
    4. press unlock

    note, that such method will work only for old security locosto-based phones.
    if you will get error while attempting to do that method - you have new security phone and should try other methods.

    server-based patch method

    1. select correct model
    2. on settings, check "signed mode", "use alternative security bypass"
    3. back to odm tab
    4. press unlock

    that method can not fix security zone.
    that method is standalone in setool2 versions, greater than 1.0

    user code reset

    1. select correct model
    2. on settings, check "signed mode"
    3. back to odm tab
    4. press unlock

    note,that some old firmware not support usercode reset, so if standart code will not work after reset, reflash phone with latest firmware.


  4. #4
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default

    FLASHING OF SEMC ODM PHONES

    1. select correct model
    2. use com/ufs as interface
    3. add to firmware area needed firmware
    4. press flash

  5. The Following 26 Users Say Thank You to the_laser For This Useful Post:


  6. #5
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default

    UNLOCKING OF SEMC ODM PHONES

    broadcom based - z300,j210,j220

    1. select model
    2. select com/ufs as interface
    3. uncheck all settings
    4. press unlock
    5. power on phone with unsupported sim card, press *<<*, enter readed codes.

    if you have "not allowed" while entering codes, just reflash phone

    calypso lite based - j110,j120,k200,k220

    1. select model
    2. select com/ufs as interface
    3. uncheck all settings
    4. press unlock

    for k200,k220 this is full unlock and security zone will be automatically fixed.
    for j110,j120 this is special firmware patch - after unlock, power on phone, press *<<* with unsupported card and enter any 8 digits as code for each lock.
    phone will accept code and unlock will be permanent.

    note, that j110,j120 phones with damaged security zone are not supported.

  7. The Following 35 Users Say Thank You to the_laser For This Useful Post:


  8. #6
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default

    POSSIBLE PROBLEMS WITH S1 PHONES

    damaged trim area , IMEI could not be read, simlocks state "tampered" or "0"

    first, we need to restore trim area, for this :

    1. select correct model
    2. on settings, check "signed mode","enable alternative security bypass"
    3. add to firmware area
    if you have neptune-based phone - W302_TA.SSW
    if you have t280,t303,r306,r300,k330,w205,Tilde phone - R300_TA.SSW
    if you have t250 phone - t250_ta.ssw
    if you have Z250,z320,t270 phone - z320_ta.ssw
    if you have j132 phone - j132_ta.ssw
    4. press flash

    you can use trim area in .bin format to restore trim area, for this select trim area in misc. edit, check "signed mode","altbypass mode","format gdfs when writing" and press "write gdfs"

    now trim area structure restored and phone should be signed with s1 signature server.
    it is recommended to restore phone original IMEI first, for this :

    1. create text file with contents:
    taread:000107D1
    2. select proper model, check on settings only "signed mode", select created file in misc. field
    3. press "write script", file will be created in form %imei%.txt
    4. look at file in notepad, you will see IMEI inside in very simple form, change IMEI to original and save file
    5. select changed file in misc. field and again press write script
    6. check with identify if you set correct IMEI, repeat 4,5 until success

    now you need to unlock phone using signature server, consult corresponding FAQ post for that.

    note, that alternative security bypass not available for phones with aid 0004, you can not fix aid004 phone with damaged trim area.

    phone simlock okay, not tampered, but phone stucked,slow,rebooting. flashing not help.

    most probably, internal file system gone to winds. you need to write fullflash from working phone or write clean file system, then reflash phone
    check support area for that files.
    please note, that all neptune-based phones can be cured with w302_fullflash,etc (check trim area repair case)
    in most cases, alternative security bypass needed for writing fullflash.

    note, that alternative security bypass not available for phones with aid 0004.

    phone can't be detected at all

    semcboot somehow got damaged ( while it is never touched by any process )

    procedure to fix:

    1. select correct model
    2. on settings check "signed mode"
    3. add EROM to firmware tab.
    if you have neptune based phone: 1207-7713_EROM_S1_NEPTUN_HS_SEMC_SIMLOCK_R7A024.sin
    if you have locosto based phone, then select situable from:
    J132_EROM_S1_LOCOSTO_HS_USB_R5A038_64k.sin
    K330_T280_T270_EROM_S1_LOCOSTO_HS_R5A028.sin
    R300_R306_T303_S1_LOCOSTO_HS_R5A031_128.SIN
    for w395 CXC1250616_EROM_S1_LOCOSTO_HS_USB_FLAFLA_R5A038.si n will do job
    T250_CXC1250616_EROM_S1_LOCOSTO_HS_R5A022.sin
    Z250_Z320_EROM_S1_LOCOSTO_HS_R5A023.sin

    4.press recovery

    check if phone trim area/simlock are okay by doing identify.
    repair simlock or trim area if needed.

    note, that semcboot repair not available for phones with aid 0004.


  9. #7
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default

    POSSIBLE PROBLEMS WITH ODM PHONES.

    phone hang, can't save photo,etc

    1. write repair flash from support area
    2. unlock phone
    3. flash phone with latest firmware


    note, that k200,k220 has two flash ic types, select samsung repair flash if you flash manu id=0xEC,
    select spansion repair flash for all other types.


  10. #8
    Administrator
    Join Date
    Feb 2010
    Posts
    18,786

    Default

    How to enter network unlock code for w150 (Yendo) phone ?


    ENTER #123456789# TO CHECK SOFTWARE AND CHECK LOCK STATUS
    ENTER #987654321# AND SELECT RED AND PUT CODE


Similar Threads

  1. HOW TO WORK WITH SEMC PDA PHONES
    By the_laser in forum F.A.Q.
    Replies: 13
    Last Post: 11-20-2013, 04:36 PM
  2. HOW TO WORK WITH A2-BASED PHONES
    By the_laser in forum F.A.Q.
    Replies: 6
    Last Post: 04-27-2012, 05:11 PM
  3. HOW TO WORK WITH A1-BASED PHONES
    By the_laser in forum F.A.Q.
    Replies: 5
    Last Post: 02-06-2010, 09:04 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •