W395 Weird Problem

[EDOComSel]

First come phone with white blank, after change flex cable, SE logo come then display become red and phone off.

Have try to flash with firmware from support but not help.

Here is log when identify :



SIGNED MODE (USING SERVER)
CFG:10001110000000
PLEASE ATTACH TURNED OFF PHONE NOW
PRESS AND HOLD "C" BUTTON...

EROM "R7A024" AID: 0001
SOFTWARE AID: 0001
SIMLOCK STATE: "NOT_TAMPERED"
LOADER AID: 0002
LOADER VERSION: "R3A011"

PHONE IMEI:35236203368396
MODEL (from GDFS): W395
FACTORY CXC: 1207-7713 R7A024
CURRENT CXC: 12175563_R1CB011
CURRENT CDA: 1221-1257_R5A
CURRENT FS: 12175582_FS_APAC-ANZ_HS_YO_R1CB011
LANGUAGE: AL
Elapsed: 12 secs.

Altough I've flash with another version identify log is not change.

Any solutions please ?

Thanks in advance

[SE MAN]

If you encounter this problem,the phone does not startup correctly after flash, please wait 2-3 minutes
then reinsert the battery and start the phone again.
The phone should now start normally and the SW has been correctly updated.

[EDOComSel]

If you encounter this problem,the phone does not startup correctly after flash, please wait 2-3 minutes
then reinsert the battery and start the phone again.
The phone should now start normally and the SW has been correctly updated.

Have try it but not help.

The_laser wrote :


most probably, internal fs gone to winds. you need write fullflash from working phone or write clean file system, then reflash phone
check support area for that files.
please note, that all neptune-based phones can be cured with w302_fullflash,etc (check trim area repair case)
in most cases, alternative security bypass needed for writing fullflash.

May help upload here, I can't find that file at support area ...

Thanks

[Amir-SkillZ]

Chk New Update and Trium Area Repair Option...

[the_laser]

w302 fullflash can be found ... guess where ? on support area in w302 folder ;)
and NOT touch trim area.

[EDOComSel]

w302 fullflash can be found ... guess where ? on support area in w302 folder ;)
and NOT touch trim area.

Have found it but when try to flash get this error :


RUNNING v0.915060/UNI
CARD SERIAL 000xxxxx
USBFLASH DRIVER VERSION 02.02.00.05
SIGNED MODE (USING SERVER)
CFG:100000000000
PLEASE ATTACH TURNED OFF PHONE NOW
PRESS "POWER ON" BUTTON SHORTLY...

EROM "R7A024" AID: 0001
SOFTWARE AID: 0001
SIMLOCK STATE: "NOT_TAMPERED"
LOADER AID: 0002
FLASH ID: "0001/307E"
LOADER VERSION: "R3A011"

PHONE IMEI:3523620336xxxx
writing "D:\setool2g\FIRMWARE\W302\w320_full_altbypass.ssw"
FATAL ERROR "SIN_HEAD_VER (Sig_fail)" IN "SECURITY_CLASS"
error while uploading HDR block
error while flashing "D:\setool2g\FIRMWARE\W302\w320_full_altbypass.ssw"
Elapsed: 16 secs.

Is this HW or still SW problem Mr. Laser ?

Thanks

[the_laser]

that is so-called "settings" problem.
please read flash file name ;)

[EDOComSel]

Problem solved, case close

Thanks Mr.Laser

"flash file name is extracted from file zip I downloaded at support area"

w320_full_altbypass.ssw very weird ?